Aruba HPE 2530 24G PoE+ Switch J9773A
Aruba HPE 2530 24G PoE+ Switch J9773A
-
24 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 type 10BASE-T, IEEE 802.3u type 100BASE-TX, IEEE 802.3ab type 1000BASE-T, IEEE 802.3at PoE+)
-
Media type: Auto-MDIX
-
Duplex: 10BASE-T/100BASE-TX: Half or full
-
1000BASE-T: Full only
EGP23,000.00
Aruba HPE 2530 24G PoE+ Switch J9773A
Aruba 2530 Series Gigabit Ethernet devices are enterprise-class, fully managed, Layer 2 edge switches delivering cost-effective, reliable, and secure connectivity for business networks. Designed for entry-level to midsize enterprise networks, these Gigabit Ethernet switches provide whole Layer 2 capabilities with enhanced access security, traffic prioritization, IPv6 host support, and optional PoE+. Aruba HPE 2530 24G PoE+ Switch J9773A model has 24 x 10/100/1000 PoE-enabled ports and four Gigabit SFP ports.
J9773A Specification
J9773A Specifications |
|
| Type | Aruba 2530-24G-PoE+ Switch |
| System specifications | |
| Ports |
|
| Memory and processor | Processor: ARM9E @ 800 MHz, 128 MB flash, 256 MB DDR3 DIMM; packet buffer size: 1.5 MB dynamically allocated. |
| Mounting | Mounts in an EIA-standard 19-inch telco rack or equipment cabinet (rack-mounting kit available); horizontal surface mounting; wall mounting. |
| Management | IMC – Intelligent Management Center; Command-Line Interface (CLI); Web browser; configuration menu; out-of-band management (serial RS-232C or Micro USB);IEEE 802.3 Ethernet MIB; Repeater MIB; Ethernet Interface MIB. |
| Performance (IPv6 Ready Certified) | |
| 1000 Mb latency | < 2.3 µs (LIFO 64-byte packets) |
| 100 Mb Latency | < 7.4 µs (LIFO 64-byte packets) |
| Throughput | up to 41.6 million pps (64-byte packets) |
| Switching capacity | 56 Gb/s |
| MAC address table size | 16000 entries |
| Physical specifications | |
| Dimensions (W x D x H) | 44.3 x 33.02 x 4.45 cm (17.44 x 13.00 x 1.75 in) (1U height) |
| Weight | 3.95 kg (8.7 lb) |
| Electrical specifications | |
| Maximum heat dissipation | 135 BTU/hr (142.42 kJ/hr), (switch only: 135 BTU/hr; combined switch + max. PoE devices: 843 BTU/hr) |
| Voltage | 100 – 127 / 200 – 240 V ac |
| Current | 3.2/1.6 A |
| Idle power1 | 25.2 W |
| Maximum power rating2 | 247 W |
| PoE power | 195 W |
| Frequency | 50/60 Hz |
| NOTE: 1: Idle power is the actual power consumption of the device with no ports connected.
2: Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated. PoE power is the total power budget available to all PoE ports. |
|
| Environmental specifications | |
| Operating temperature | 0° to 45°C (32° to 113°F) |
| Operating relative humidity | 15% to 95% @ 40°C (104°F), noncondensing |
| Non-operating/storage temperature | -40° to 70°C (-40° to 158°F) |
| Non-operating/storage relative humidity | 15% to 90% @ 65°C (149°F), noncondensing |
| Altitude | Up to 3 km (10,000 ft) |
| Acoustic | Power: 39.6 dB, Pressure: 43.9 dB |
| Safety agency certifications | |
| Safety | UL 60950-1; CAN/CSA 22.2 No. 60950-1; EN 60825; IEC 60950-1; EN 60950-1 |
| NOTE: IEEE 802.3az applies to Gigabit models only; IEEE 802.3at and IEEE 802.3af apply to PoE+ models only. When using SFPs with this product, SFPs with revision “B” or later (product number ends with the letter “B” or later, e.g., J4858B, J4859C) are required. | |
HPE 2530 24G PoE+ Switch DataSheet
